How to: banana pi BPI-M3 install BPI-WiringPi
How to force m3 to allow exporting gpio? example: echo 7 > /sys/class/gpio/export-su: echo: write error: Invalid argument
View Article1st Banana Pi M3 review
dear tkaiser , i have let Judy send a BPI-M2+ to you. you have help us many ,and i like you. :smile, you have do many test on our product, it is a hard work. thank you again.
View ArticlePlease, update Specs of M3
dear Tido . you have help us many , are you like to test a BPI-M2+ board, if you want , i can let judy send a free sample to you.
View ArticleBPI-M3 using SSD on SATA-Port
Hi Tido,I brought the image to on-board eMMC.Here now all the results with iozone: iozone -e -I -a -s 100M -r 4k -r 16k -r 512k -r 1024k -r 16384k -i 0 -i 1 -i 2 from Dragan: random random kB reclen...
View ArticleBPI-M3 using g_ether
Thank you for the link, this did not help me. Running the commandecho 2 > /sys/bus/platform/devices/sunxi_usb_udc/otg_roledoes not have any effect on my system. I don't see the USB-device with...
View ArticleClik here to view.
How to get the OTG working on linux for BPI-M3
morpheux74: echo 2 > /sys/bus/platform/devices/sunxi_usb_udc/otg_role How could you load the gadget module g_ether? This module does not exists on any image I tried out ...
View Article1st Banana Pi M3 review
Sup, can we get info it there will be some kind of normal apt\pac repo for the systems to not go the fancy burning the img update procedure?Also the board works like a charm, got hard wired it to a...
View ArticleClik here to view.
BPI-M3 using SSD on SATA-Port
tomde: The worst results are obtained with an SD card. The on-board eMMC provides for the read mode about 2 times faster compared to a SSD disk on USB2.0 port. In write mode, they differ slightly. Thx...
View ArticleClik here to view.
BPI M1+ UART3 (TTYS2) not Working
rohitsivakumar: 2,4, 5,6,7 Rohit, UART4 is not accessible from pin header in BPI-M1+, I think it is on BananaPro.BPI-M1+ has the following UARTs reported on GPIO connector UART 2/3/5/6/7. The...
View ArticleClik here to view.
Shutdown by network (IP) Packet
Hi jwka, using ssh and issuing shutdown -h can do the thing. Some hints here: superuser.com Is it possible to shutdown remote Computers without inputing the password? asked by sunpy on 02:40PM - 04...
View ArticleHow to get the OTG working on linux for BPI-M3
This module is set by default as a built-in in the kernel configuration, so you don't have to manually load it, it's automatically loaded at startup.If you really need to load it on demand you can try...
View ArticleClik here to view.
LCD display lemaker on M3
Hi, I'm new in this area and I just bought a banana Pi m3 and then I got an LCD screen 5" (made by lemaker) touchscreen hoping that by connecting it to the M3 everything was fine, but then I found out...
View ArticleBanana Pi M1 - Case for 2,5 inch ssd
Hi I want to build a cheap webserver for only 200 users, who will bareley connect more then twice a month.But the amount of data is nevertheless huge.I want to connect a cheap ssd with sata to the...
View ArticleGB Ethernet shield to have 2 connections on a Beowulf head node
Anybody have suggestions on how to add a second GB Ethernet connection on a BPI-M3 ? I would use the BPI-M3 in a 4-8-16 nodes Beowulf cluster. The head node needs 2 connections ... one to the internal...
View ArticleGB Ethernet shield to have 2 connections on a Beowulf head node
for A83T ,just support one ethernet port, if we try do add a Lan ,must add a extend swithc or rourter chip on bard, but all switch chip have support 5 port RJ45, so , it become same as BPI-R1:) we now...
View ArticleDoes the M3 support 1-Wire tecnologie?
My Question is easy does any Linux Destribution of the M3 Support the 1-Wire Tecnologie. I Activated it BSP but if i want to connect an 1 wire sensor it isn't shown! I also tested, is there any w1...
View ArticleBPI M1+ UART3 (TTYS2) not Working
Thanks for sharing the details. On the M1+ CON-3, there are three uarts exposed - Uart7, Uart3, Uart2. I was able to get uart7 (ttyS3), uart2 (ttyS1) working. I suppose ttyS2 (Uart-3) is the issue. In...
View ArticleClik here to view.
Does the M3 support 1-Wire tecnologie?
this maybe help you.https://bananapi.gitbooks.io/bpi-accessories/content/lm75_temperature_sensor_module.html we also have do this module, but not use BPI-M3, but all maybe easy to control. BPI-GSM...
View ArticleGB Ethernet shield to have 2 connections on a Beowulf head node
Use a GbE Ethernet USB dongle or another device as head node.
View ArticleDoes the M3 support 1-Wire tecnologie?
You need 3 modules to try out with modprobe: w1-sunxi, w1-gpio and w1-therm. Don't know whether they include these in the kernel since they ignored all help offerings in the past.
View Article